# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# ---------------       `install-mbr(8)', `/usr/share/doc/lilo/',
#                       and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run `lilo' after you make changes to this     |
# | conffile, `/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run `lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.

# # In case you use devfs
# boot=/dev/ide/host0/bus0/target0/lun0/disc
boot=/dev/hda

# Specifies the device that should be mounted as root. (`/')
#

# root=/dev/ide/host0/bus0/target0/lun0/part3
root=/dev/hdb1

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
#
install=/boot/boot.b

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like.  If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress.  `single-key' goes with the `alias' lines in the
# `image' configurations below.  eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
message=/boot/bootmess.txt
	prompt
#	single-key
#	delay=100
	timeout=30

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# Boot up Linux by default.
#
default=linuxmenu

other=/dev/hdb
	label=linuxmenu

# image=/boot/vmlinuz-2.6.7
# 	initrd=/boot/initrd.img-2.6.7
# 	label=initrd267
# 	read-only
# #	restricted
# #	alias=5

# image=/boot/vmlinuz-2.6.3customkernel
# 	initrd=/boot/initrd.img-2.6.3customkernel
# 	label=initrd263
# 	read-only
# #	restricted
# #	alias=5

# image=/boot/vmlinuz-2.6.3-1-686
# 	initrd=/boot/initrd.img-2.6.3-1-686
# 	label=initrd263orig
# 	read-only
# #	restricted
# #	alias=5

# image=/boot/vmlinuz-2.4.25
# 	label=lvm2-2.4.25
# 	read-only
# #	restricted
# #	alias=1

# image=/boot/vmlinuz-2.4.22-xfs
# 	label=lvm2-2.4.22
# 	read-only
# #	restricted
# #	alias=1

# #image=/boot/vmlinuz-2.4.12-xfs
# #	label=Linux2412
# #	read-only
# ##	restricted
# ##	alias=1

#image=/boot/vmlinuz-2.4.12-xfs
#	append="root=/dev/rd/0 init=/linuxrc"
#	initrd=/boot/initrd-2.4.12
#	label=initrd2412
#	read-only
##	restricted
##	alias=5

# image=/boot/memtest86.bin
# 	label=memtest
# 	read-only
# #	restricted
# #	alias=1

#image=/boot/vmlinuz-2.4.14-xfs
##	append="root=/dev/ram0 init=/linuxrc"
#	initrd=/boot/initrd-2.4.14
#	label=initrd2414
#	read-only
##	restricted
##	alias=5

# image=/boot/vmlinuz-2.4.17-xfs
# #	append="root=/dev/ram0 init=/linuxrc"
# 	initrd=/boot/initrd-2.4.17
# 	label=initrd2417
# 	read-only
# #	restricted
# #	alias=5

# # this is the first lvm2 kernel (has the latest xfs too; shudder)
# image=/boot/vmlinuz-2.4.19-xfs
# 	label=lvm2-2.4.19
# 	initrd=/boot/initrd.img-2.4.19-xfs

#image=/boot/vmlinuz-2.4.14-xfs
#	label=Linux2414
#	read-only
##	restricted
##	alias=1

# # DO NOT CHANGE THIS KERNEL!! This is the original!
# image=/boot/vmlinuz-2.2.14-stock
# 	label=stock
# 	read-only
# 	optional
# #	restricted
# #	alias=4

# image=/boot/vmlinuz-2.2.17
# 	label=lin22
# 	read-only
# 	optional
# #	restricted
# #	alias=2

#image=/boot/vmlinuz.old
#	label=prev
#	read-only
#	optional
##	restricted
#	alias=3

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#	label=HURD
#	restricted
#	alias=4

other=/dev/hda1
	label=dos
#	restricted
#	alias=3